Request AudioReQuest Z.Series Manual de usuario descargar pdf (Pagina 8)

pro2_av2_cp2_cp2e_rack2_pac2_4.003.0015.txt

timeout.

- Handled a problem where SSL would not work if the webserver was disabled.

- Now close active Ethernet TCP sockets on a LAN when the link layer is lost.

- Fixed the problem in which SSL redirection was not working properly if the

SSLport was not set to the default (443) port. That is, if SSL port is set to

"abc", and the webport is default, and SSL is on, then

"http://xxx.yyy.zzz.kkk" should be redirected as

"https://xxx.yyy.zzz.kkk:abc/index.html".

- Fixed a bug where the system would reboot if connected to a poll accelerator

with a crossover cable and the poll accelerator was rebooted.

- Modified the ClientServer driver so that the connection task will be killed

for Clients when the connect line is disabled. Handles a problem seen when a

client is trying to reconnect and the connect line is toggled in the program.

This would lead to a condition where the state would alternate between

connected and broken remotely.

- Fixed a problem with CIP devices using DHCP updating their IP addresses from

behind routers.

- Reporting of Rx Overrun errors now needs the ShowExtra command set to ON.

- Fixed a bug where the system would bog down if hit with a browser and no web

pages had been loaded.

- Corrected a problem with TCP Clients where the timeout for dead connections

was exceedingly long. This occurred when the first data packet tranmitted

happened some significant time after the connect.

- Now send the offline message to the Offline helper for gateway nodes when

link is lost.

- Mark nodes that fail registration (no entry in IP table) as offline so that

the offline helper will work.

- Changed the TCP client reconnection task to resolve the name on each

connection attempt. This will help reconnect in a DHCP environment where the

address changes and needs to be resolve after the DNS cache times out.

- Now close all active sockets when DHCP address is released.

- Modified the IP table display (IPTABLE) to include two new types "ESlav" &

"EMstr" and two new status labels "DNS LOOKUP" & "BAD LOOKUP".

- Fixed a bug where if setting the password through the NAT setup pages

failed, the wrong page was referenced and a 404 file not found message was

displayed.

- Fixed a problem where, if the NVRAM Disk was corrupted, then

the internal file system would not load. This would appear that the program

was erased and the IP setting lost.

- Front Panel Percent Display Objects have been modified to

round instead of truncate.

- Fixed XSig issue where the error "Signal Mismatch in Receive of Intersystem

Communications" would be generated.

- Fixed a crash that occurred when a Pro2 front panel was displaying a page

with a page join, multiple Ethernet consoles were open, and the program was

reset.

- Long delays > 42950s will now work.

- Fixed a problem with the IR serial that was corrupted in some cases.

- Fixed a problem that was seen when a program contained a Slave

system & the Front Panel symbol of the slave was destroyed, a message like "No

Parent or Driver for Slot-09" (or whatever the Cresnet Slot was).

- Fixed a problem with Ramps where a negative transition below the min

value would be seen as a large value. This fixes an issue seen with the

Analog Ramp where when it was near 0%, it would sometimes jump to close to

100%.

- Fixed a problem when the RAM symbol where if you had Store=1, Recall=1,

Select#1=1, that the RAM/DRAM would not work correctly if you had a different

signal name on an input & output line. If the input and output signal were

tied together, it would work fine.

- Fix issue with using Identify Transmitter in Viewport. As of 3.026, Identify

Transmitter would not work unless there was at least one transmitter defined

on the gateway (any ID). This will allow behavior as before 3.026 - load a

program with only the gateway defined on the correct ID (or slot, like in an

Page 8

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 22 23

Comentarios a estos manuales

Sin comentarios

Request AudioReQuest Z.Series Manual de usuario Pagina 8

Comentarios a estos manuales