pro2_av2_cp2_cp2e_rack2_pac2_4.003.0015.txt
- Added console command GMTOFFSET to set the offset from Greenwich Mean Time.
This setting will be stored non-volatilely. Also added two SIMPL+ functions,
GetGmtOffset(), SetGmtOffset() functions.
- Added new format to Clockdriver symbol. Format 6d - Australia, (Lord Howe
Island, New South Wales, South Australia, Victoria, Australian Capital
Territory) - Last Sunday in Oct to Last Sunday in March.
- Put proper GMT offset on outbound mail time, using the EEPROM stored value
from the GMTOFFSET command. Note that when upgrading systems that did not
have this setting, GMTOFFSET is init'd to 0 (anyone on the East Coast USA will
report that their GMT offset isn't functioning anymore unless they set this;
it used to be hardcoded to EST).
- Revised Super Debugger to accept dotted notation for an address & allow
Alpha's, i.e:
sdebug -DON C0x25.A
Would mean turn on debugging for Cresnet ID 0x25 Port A.
Alternatively
sdebug -DON S9.0x25.A
in a Pro2 model would mean Slot 9, ID 0x25 beneath is, Port A beneath
that (Cresnet ID 0x25, Port A).
- Fixed a bug in handling CNWP-xx panels.
- Fixed a bug where a SIMPL+ pulse statement with a 0 time caused a reboot.
It now causes a logic wave pulse and generates a warning to the error log.
- Fixed front panel extenders for Rack2.
- Fixed a bug in SendMail() where the processor would crash when CC field was
blank.
- Fixed a bug where the SIMPL+ RetimeWait() function would cause a crash if
the wait specified did not exist.
- Fixed XSIG encoding to handle embedded \xFF in strings.
- Fixed a problem where the Pac2 hub segments were not independent. A short
on one leg would bring the whole hub down.
- Changed XSIG receive: If an empty string is received, it is now propagated
to logic.
- Changed "Prev" "Next" buttons on error log screen to "First" and "Last" to
faciliate jumping to the top/bottom of the log. The up and down buttons on
the right side (between menu & backlight) still function to scroll one line at
a time.
- Added analog signals to the Mouse symbol for X & Y axis for same coordinates
as MS Mouse (-127 to +127).
- Changed the SDPM symbol to check ranges on the NET ID value (03 to FF).
This fixes errors occasionally seen with the Crestron password module.
- Modified the TimeOffset symbol to prevent symbol from doing anything with
the outputs until all 3 inputs have settled. This means that if you want
either the hours to be zero (i.e. 12AM) or the minutes to be zero, then you
must INIT the values to 0 rather than simply tie a 0 to the analogs.
- Slave control systems handle bursts of traffic better.
- Use new version reporting scheme major.minor.build number.
Known issue
- CT-1000 or LC-1000 firmware v6.203.0 clock object stops after restarting
SIMPL program. Must reboot CT/LC-1000 panel for clock to run.
Build: 3.137(Release)
Sept 3, 2004
- Initial implementation of the UPX-2 full model.
- Initial implementation of the TPMC-10 full model.
- New symbols (Requires Library Update >= 304):
Double Precision Init
Astroclock with Enable Input & Enabled Output
Time Offset with Enable Input
Stepper with Progress & Cancel.
- New device extenders (Requires Library Update >= 304):
Page 5
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales