Request AudioReQuest Z.Series Manual de usuario descargar pdf (Pagina 22)

pro2_av2_cp2_cp2e_rack2_pac2_4.003.0015.txt

defined for that button on the RF Mouse definition in the program.

-Fix problem where RTS and break signals on CNX-COM2 card would have no effect

-Fix problem with the WEBPORT command where the port would appear to change but the

Web Server would not listen on the new port

-In PresetV, don't create ramping analog on output until the end of the current

logic solution. This handles the case where a Preset digital arrives in an earlier

logic wave than the Level values. This is done for compatibility with older

generation control systems.

***Since Version 1.008 (Release)

-Fix problem with "Analog Sample" (Speedkey: SAMPLE) symbol where it required the

[sample_change] input to be filled in, even though it is marked as optional.

-Fix RS-422 and RS-485 problems on internal COM ports and plug-in COM cards

-Fix problem with Web Server where to access the Web Server through a router the URL

needed to contain the file name. For example: http://myrack.com/main.html would

work while http://myrack.com would not.

-Fix problem loading firmware to a CNMK-2

***Since Version 1.001 (Release)

-Fix problem where control system would lock up when serving a web file that

exceeded 100k

-Fix potential lock-up with an oscillator if the gate goes low at the exact time the

oscillator's high time or low time expires

-Generate a notice when an ethernet device comes online and a warning when it goes

offline

-Switch front panel back to main menu on a program load, program reset or an erase

program

-Fix lock-up problem when an IP address other than 127.0.0.1 was assigned in the IP

table for ActiveCNX or WEB page interfaces

-Fix problems using Ethernet Intersystem Communications devices to talk between

2-Series Control Systems

-On program reset, all analogs and digitals will be reset on the front panel.

-Fix problem on program reset where built-in I/O ports would report an erroneous

momentary closure on some inputs.

-Fix problem with sending IR to TVAV and CNXRMC/CNXRMCLV boxes

-Fix problem with Erase Program (Program would stop but files were not deleted)

-In CNXVTC-3 card, fix problem where mute line was working in reverse. (i.e. digital

low would mute)

-Fix problem where CTS was not reported properly for internal COM ports C-F

-In Analog Buffer, only propogate analog changes if the input signal and output

signal have different values (This is to be compatable with previous generation

Control Systems)

-When running Test Manager with the option "Trace Only Signals in Status Window",

make sure debug flags remain set after a program reset

-Changed the file system startup so that bypass program mode will now cause the

system to validate the file system before loading it. This will allow the ethernet

console to

still be opened if a program is bypassed.

-Fix crash on program reset that occured if there were no devices in the program

that could be analyzed using the com analyzer (e.g. no COM ports defined in the

program)

-Fix potential problem with Analog Ramp when the time parameter exceeded 655 seconds

-Fix problem in Analog to Indirect Text symbol where the indirect text field was

being offset by one (e.g. specifying a field of 8 would actually send indirect text

to field 9)

-Fix problem with all Analog Buffers where if a ramping symbol (e.g. Analog Ramp,

Preset, etc.) is jammed to it's output and a non-ramping symbol is attached to it's

input the ramping operation on the output would be cancelled when a transition cam

in on it's input.

-Fix crash that would occur if a COM or IR card had no ports defined below it.

-Use a more accurate estimate for string lengths in Simpl+ makestrings when printing

out integer values. Previously the string would have to be large enough to store

the largest possible integer now the string only needs to be large enough to store

Page 22

1 2 ... 17 18 19 20 21 22 23

Comentarios a estos manuales

Sin comentarios

Request AudioReQuest Z.Series Manual de usuario Pagina 22

Comentarios a estos manuales