pro2_av2_cp2_cp2e_rack2_pac2_4.003.0015.txt
message is generated.
- Fixed a problem with the AnalogIncrement so that on mute, if the Feedback
input was defined, it reads the value to restore from that signal (for when it
unmutes), otherwise, read the value to save from the output signal.
- Handle software watchdog timeouts when connecting via SSL.
- Removed DHCP release/renew information from the EEPROM command.
- Added SSL mode to ESTATUS command.
- Added code to force an immediate DHCP retry if new link is established on
Lan A and the DHCP failed. This handles the case where DHCP was enabled and
the LAN A cable was unplugged. Previously, the processor waited 15 minutes
before retrying to get a DHCP address.
Build: 3.080(Release)
August 15, 2003
- Fix webserver issue when accessing a web page via the WAN address of a
C2ENET-2 card when the 2 Series system was behind a router. This issue
was introduced in 3.061.
- Fix issue with the "function main()" of SIMPL+ modules not being terminated
on a Program Reset (F10 or SW-R button). These issues would cause messages
such as "Warning: Module -48-247 : S2_EventSch_v1_2 at line 1039: digital
input", and potentially a system reboot.
- Fix CLW modules so that if no "level-out" signal is defined, the system
will not crash.
- Fix PresetV so that a cut will not cause the PresetV output to first go
to the opposite extreme from which it was fading, then to the proper extreme
(i.e. fade from 0% to 100%. If you did a cut at 50%, it would go to 0%
then to 100%)
- Fix issue where the system time/date would get corrupted or generate "Bad
Time/Date" messages or generate "DST Helper" errors with the Clock Driver
symbol. Specifically, the time/date could get corrupted if you had a
Clock Driver symbol in your program with DST set to 1d or greater.
- Fix so errors about packet type 1C are not generated through D3 Pro when
using Real Time mode to control a circuit.
- Fix SIMPL+ error message that said "digital input" to say "No digital input
signal defined at {position} on symbol wrapper"
- CLX/CLW lighting device interface symbols now clip and issue an error if
the fade time exceeds (approximately) 46.6 hours.
- Fixed a problem displaying the Ethernet status in a dual port card when the
LAN A was disabled. Also, only display speed and duplex settings if the link
is valid.
- Fixed a bug introduced in 3.061 where TCP client devices did not show up
as such in the IP table display.
- Added code to prevent a deadlock situation (processor appears to hang) when
the watchdog resets the processor.
- Increased the delay after initializing the PHY to fixed speed/duplex settings
(not AUTONEG).
- Put in code to handle a race condition on closing connections that caused the
system to freeze when hit with a port scan.
- Changed the IP table display to show the programmed port values for TCP
clients and TCP servers.
- Fixed a problem with the RouteE and RouteC symbols that resulted in 3.061
from trying to handle mismatched list sizes that ended up making all lists on
both E's and C's have to be identical in size.
- Correct issue where an empty string would not propagate through the route
symbols correctly unless a "Make String Permenant" symbol was tied to the
destination string.
- Added support for new TCP2UDP messages to deal with authenticating gateway
(activeCNX or webpage) connections. Use of this will require an upgrade to
the eControl applications. The authentication only occurs when SSL is
enabled.
- Fixed a bug introduced in 3.061 that caused the system to reboot if the NAT
Page 10
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales